CryoJet: Difference between revisions

Content deleted Content added

Inline

Latest revision as of 16:12, 12 September 2023

CryoJet / IceJet is a derivative of the machining process called abrasive waterjet (AWJ) machining.^{[citation needed]} CryoJet/IceJet technology uses ice particles made of water coming from a running water or freshwater system to cut material. While the ice particles are cutting material, they melt and go into the water tank of the machine. The pressurized water acting as a cutting jet can be re-used, with adequate filtering, creating a closed water circuit.^{[citation needed]} However, the majority of users do not re-use the water. If more widely used, CryoJet may produce a drastic reduction in the amount of abrasive waste spill currently produced during the water jet cutting process, as no mineral abrasive is used by this technology.^[1]

Ice Generation

There are two different approaches to ice particles generation.

The ice particles can be prepared beforehand using an ice particle generator, stored in a reservoir and then fed to the conventional entrainment based jetting head.
The need for ice particle generators, cooled storing facilities and conveying equipment can be eliminated by forming the ice particles in situ during the water jet formation. The ice jet in this case is generated either by sub-cooling of pressurized water and controlled phase transformation during pressure relaxation in the jet nozzle, or by phase transformation by entrainment of cold liquid gases such as liquid nitrogen (N₂) (see: Phase diagram of water).

Advantages

In comparison to other cutting technologies such as plasma cutting or laser cutting, the traditional water jet cutter technology produces extra waste material (in addition to the kerf material itself).^[2] Above all, the use of mineral abrasives for improving the performance of the cutting jet is increasingly becoming a problem. Firstly, as a consumer, it is the most significant cost factor of the process, and secondly, it represents more than 99% of the waste material generated during cutting processes. Therefore, it requires a complex and expensive waste management system. Consequently, several approaches for eliminating the need of mineral abrasives while maintaining its powerful cutting performance have been discussed by researchers^{[citation needed]}.

History

The first experimental researching done on Ice Jet technology dates back to 1982, when the first ice particles were created by mechanical crushing of bigger ice particles. Galecki and Vickers [Gal82] performed surface cleaning and abrading with an ice-blasting technique. The ice particles were produced by refrigeration of 3 cm blocks, which were then transferred to a container of liquid nitrogen where the ice cubes were further cooled, and finally transferred to a mechanical crusher where they were crushed and subsequently entrained into a nozzle.

Also in 1982, Krzysztof et al. showed that one of the most promising applications for ice particles is the cleaning technology. Water ice is readily available, inexpensive material, which can be used as a green manufacturing tool. Only water, electricity and refrigerant are needed for the fabrication of this tool, which can be produced just in time. The use of ice tools might practically prevent pollution and eliminate work piece contamination.

Since then, several researchers have developed equipment for producing ice particles, mainly for cleaning [Set98], polishing [His94] and surface decontaminating [Ges99] purposes. Newer research works [Shan05] and [Klu05] show that ice particles can be used for water jet applications such as cleaning, degreasing and cutting, with its concept based on the convective heat transfer between a cold cryogenic gas and atomized water droplets. Ice particles are formed inside the system by transferring latent heat of water droplets to liquid nitrogen. Kluz et al. show that the air-ice particle stream can be generated and applied for processing of bio materials and food. The performed studies showed feasibility and effectiveness of the use of fine ice powder as an abrasive, being the energy effectiveness of the process acceptable and the technology rather simple. Anyway, the process productivity is less than when using mineral abrasive particles.

A similar technology is the high pressure hybrid water-abrasive-ice jet treatment. Such technology is based on a high- pressure abrasive-water jet with addition of dry-ice pellets CO₂. Borkowski et al. [Bor03] show that effectiveness of surface treatment with the hybrid jet depends on the quality of ice particles.

References

^ "abrasive jet machining: Topics by Science.gov". www.science.gov. Retrieved 2018-08-31.
^ "Laser cutting vs. plasma cutting - standard metal cutting processes". www.teskolaser.com. Retrieved 2018-08-31.

[1] "abrasive jet machining: Topics by Science.gov". www.science.gov. Retrieved 2018-08-31.

[2] "Laser cutting vs. plasma cutting - standard metal cutting processes". www.teskolaser.com. Retrieved 2018-08-31.

[1]

[2]

@@ Line 1: / Line 1: @@
-{{multiple issues|cleanup=January 2012|copy edit=January 2012|essay-like=January 2012|wikify=January 2012}}
+{{multiple issues|{{more citations needed|date=September 2018}}
+{{essay-like|date=January 2012}}
-'''CryoJet''' / IceJet<br />
+{{cleanup|date=January 2012}}}}
-is a derivative of machining process called abrasive waterjet (AWJ) machining (water jet cutter). Regarding the creation of ice particles, the use of CryoJet/IceJet technology means to use [[ice]] particles made of water coming from running water or freshwater system. These particles are introduced into the water jet cutter machine and they are used to cut material. When the ice particles are cutting material they melt and go into the water tank of the machine. The pressurized water acting as a cutting jet could be re-used, by filtering adequately and entering again the high pressure pump. Thus, a closed circuit can be established. Some of the end-users reuse the water, although the majority of them do not re-use it. If an easy methodology, with clear steps is developed, end users will be convinced for doing it. CryoJet promise drastic reduction in the amount of abrasive waste spill currently produced during the water jet cutting process. For that, a pseudo abrasive material, namely “water ice” is be used instead of the mineral abrasive.
+[[File:Jet z izmenjevalnikom v2 not transparent.png|thumb|IceJet system with sub-cooled pressurised water]]
+'''CryoJet''' / IceJet is a derivative of the machining process called [[water jet cutter|abrasive waterjet (AWJ) machining]].{{citation needed|date=August 2018}} CryoJet/IceJet technology uses [[ice]] particles made of water coming from a running water or freshwater system to cut material. While the ice particles are cutting material, they melt and go into the water tank of the machine. The pressurized water acting as a cutting jet can be re-used, with adequate [[Water filter|filter]]ing, creating a closed water circuit.{{citation needed|date=August 2018}} However, the majority of users do not re-use the water. If more widely used, CryoJet may produce a drastic reduction in the amount of abrasive waste spill currently produced during the [[water jet cutting]] process, as no mineral [[abrasive]] is used by this technology.<ref>{{Cite web|url=https://www.science.gov/topicpages/a/abrasive+jet+machining|title=abrasive jet machining: Topics by Science.gov|website=www.science.gov|language=en|access-date=2018-08-31}}</ref>
-There are two different approaches to ice particles generation. The ice particles can be prepared beforehand, stored in a reservoir and then finally fed to the conventional entrainment based jetting head, or they can be generated in situ during the water jet formation itself. This eliminates the need for expensive ice particle generators, cooled storing facilities and conveying equipment. Therefore, there are two technological ways for water ice particle formation:
-- On the one hand, the generation of ice particle and subsequent entraining into the pressurized water jet.
-- On the other hand, the generation of an ice jet by sub-cooling of pressurized water and controlled phase transformation while pressure relaxation in the jet nozzle, or by phase transformation by entrainment of cold liquid gases such as [[liquid nitrogen]] (N2)(see: [[Phase diagram of water]])
+==Ice Generation==
-[[File:Jet z izmenjevalnikom v2 not transparent.png|thumb|IceJet system with sub-cooled pressurised water]]
+There are two different approaches to ice particles generation.
+*The ice particles can be prepared beforehand using an ice particle generator, stored in a [[reservoir]] and then fed to the conventional entrainment based jetting head.
+*The  need for ice particle generators, cooled storing facilities and conveying equipment can be eliminated by forming the ice particles in situ during the water jet formation. The ice jet in this case is generated either by sub-cooling of pressurized water and controlled phase transformation during pressure relaxation in the jet [[nozzle]], or by phase transformation by entrainment of cold liquid gases such as [[liquid nitrogen]] (N<sub>2</sub>) (see: [[Phase diagram of water]]).
+==Advantages==
+In comparison to other cutting technologies such as [[plasma cutting]] or [[laser cutting]], the traditional [[water jet cutter]] technology produces extra waste material (in addition to the [[Saw|kerf]] material itself).<ref>{{Cite web|url=http://www.teskolaser.com/laser_cutting2.html|title=Laser cutting vs. plasma cutting - standard metal cutting processes|website=www.teskolaser.com|access-date=2018-08-31}}</ref> Above all, the use of mineral abrasives for improving the performance of the cutting jet is increasingly becoming a problem. Firstly, as a [[consumer]], it is the most significant cost factor of the process, and secondly, it represents more than 99% of the waste material generated during cutting processes. Therefore, it requires a complex and expensive [[waste management]] system. Consequently, several approaches for eliminating the need of [[mineral]] abrasives while maintaining its powerful cutting performance have been discussed by researchers{{citation needed|date=February 2014}}.
+==History==
+The first experimental researching done on Ice Jet technology dates back to 1982, when the first ice particles were created by mechanical [[Crushing (execution)|crushing]] of bigger ice particles. Galecki and Vickers [Gal82] performed surface cleaning and abrading with an ice-blasting technique. The ice particles were produced by [[refrigeration]] of 3&nbsp;cm blocks, which were then transferred to a container of [[liquid nitrogen]] where the ice cubes were further cooled, and finally transferred to a mechanical crusher where they were crushed and subsequently entrained into a [[nozzle]].
+Also in 1982, Krzysztof et al. showed that one of the most promising applications for ice particles is the cleaning technology. Water ice is readily available, inexpensive material, which can be used as a green manufacturing tool. Only water, electricity and refrigerant are needed for the [[Manufacturing|fabrication]] of this tool, which can be produced just in time. The use of ice tools might practically prevent pollution and eliminate work piece [[contamination]].
-In comparison to other cutting technologies such as [[plasma cutting]] or [[laser cutting]], the Abrasive Water Jet technology produces extra waste material (in addition to the kerf material itself). Above all, the use of mineral abrasives for improving the performance of the cutting jet is increasingly becoming a problem. Firstly, as a consumable, it is the most significant cost factor of the process, and secondly, it represents more than 99% of the waste material generated during cutting processes. Therefore, it is requiring a complex and expensive waste management system. Consequently, several approaches for eliminating the need of mineral abrasives while maintaining its powerful cutting performance have been discussed by researchers.
+Since then, several researchers have developed equipment for producing ice particles, mainly for cleaning [Set98], polishing [His94] and surface decontaminating [Ges99] purposes. Newer research works [Shan05] and [Klu05] show that ice particles can be used for water jet applications such as cleaning, degreasing and cutting, with its concept based on the convective heat transfer between a cold cryogenic gas and atomized water [[Drop (liquid)|droplets]]. Ice particles are formed inside the system by transferring latent heat of water droplets to liquid nitrogen. Kluz et al. show that the air-ice particle stream can be generated and applied for processing of bio materials and food.
-History<br />
+The performed studies showed feasibility and effectiveness of the use of fine ice powder as an abrasive, being the energy effectiveness of the process acceptable and the technology rather simple. Anyway, the process productivity is less than when using mineral abrasive particles.
-The first experimental researchs of Ice Jet technology dates back to 1982, when the first ice particles were created by mechanical crushing of bigger ice particles. Galecki and Vickers [Gal82] performed surface cleaning and abrading with an ice-blasting technique. The ice particles were produced by refrigeration of 3&nbsp;cm blocks, which were then transferred to a container of liquid nitrogen where the ice cubes were further cooled, and finally transferred to a mechanical crusher where they were crushed and subsequently entrained into a nozzle. Also in 1982, Krzysztof et al. showed that one of the most promising applications for ice particles is the cleaning technology. Water ice is readily available, inexpensive material, which can be used as a green manufacturing tool. Only water, electricity and refrigerant are needed for the fabrication of this tool, which can be produced just in time. The use of ice tools might practically prevent pollution and eliminate work piece contamination.
-Since then, several researchers have developed equipment for producing ice particles, mainly for cleaning [Set98], polishing [His94] and surface decontaminating [Ges99] purposes. Newer research works [Shan05] and [Klu05] show that ice particles can be used for water jet applications such as cleaning, degreasing and cutting, with its concept based on the convective heat transfer between a cold cryogenic gas and atomised water droplets. Ice particles are formed inside the system by transferring latent heat of water droplets to liquid nitrogen. Kluz et al. show that the air-ice particle stream can be generated and applied for processing of bio materials and food.
-The performed studies showed feasibility and effectiveness of the use of fine ice powder as an abrasive, being the energy effectiveness of the process acceptable and the technology rather simple. Anyway the process productivity is less than when using mineral abrasive particles. A similar technology is the high pressure hybrid water-abrasive-ice jet treatment. Such technology is based on a high- pressure abrasive-water jet with addition of dry-ice pellets CO2. Borkowski et al. [Bor03] show that effectiveness of surface treatment with the hybrid jet depends on the quality of ice particles.
+A similar technology is the high pressure hybrid water-abrasive-ice jet treatment. Such technology is based on a high- pressure abrasive-water jet with addition of [[Dry ice|dry-ice]] pellets [[Carbon dioxide|{{CO2}}]]. Borkowski et al. [Bor03] show that effectiveness of surface treatment with the hybrid jet depends on the quality of ice particles.
+==References==
+{{Reflist}}
 [[Category:Machining]]