Bit banging
 | This article needs additional citations for verification. (July 2014) |
In computer engineering and electrical engineering, bit banging[1] or bit bashing[citation needed] is a term of art for any method of data transmission that employs software as a substitute for dedicated hardware to generate transmitted signals or process received signals. Such software directly sets and samples the states of GPIOs (e.g., pins on a microcontroller) to transmit and receive, respectively, and is responsible for meeting all timing requirements and protocol sequencing of the signals. In contrast to bit banging, dedicated hardware (e.g., UART, SPI, I²C) satisfies these requirements and, if necessary, provides a data buffer to relax software timing requirements. Bit banging can be implemented at very low cost, and is commonly used in embedded systems.[2]
Bit banging allows a device to implement different protocols with minimal or no hardware changes. In some cases, bit banging is made feasible by newer, faster processors because more recent hardware operates much more quickly than hardware did when standard communications protocols were created.
C code example
[edit]The following C language code example transmits a byte of data on an SPI bus.
// transmit byte serially, MSB first
void send_8bit_serial_data(unsigned char data)
{
int i;
// select device (active low)
output_low(SD_CS);
// send bits 7..0
for (i = 0; i < 8; i++)
{
// consider leftmost bit
// set line high if bit is 1, low if bit is 0
if (data & 0x80)
output_high(SD_DI);
else
output_low(SD_DI);
// pulse the clock state to indicate that bit value should be read
output_low(SD_CLK);
delay();
output_high(SD_CLK);
// shift byte left so next bit will be leftmost
data <<= 1;
}
// deselect device
output_high(SD_CS);
}
Considerations
[edit]The question whether to deploy bit banging or not is a trade-off between load, performance and reliability on one hand, and the availability of a hardware alternative on the other. The software emulation process consumes more processing power than does supporting dedicated hardware. The microcontroller spends much of its time sending or receiving samples to and from the pins, at the expense of other tasks. The signal produced usually has more jitter or glitches, especially if the processor is also executing other tasks while communicating. However, if the bit-banging software is interrupt-driven by the signal, this may be of minor importance, especially if control signals such as RTS, CTS, or DCD are available. The implementation in software can be a solution when specific hardware support is not available or requires a more expensive microcontroller.
See also
[edit]- Bit manipulation
- Bit stream
- Bit twiddler (disambiguation)
- Bit-serial architecture
- 1-bit architecture
- Fast loader
- Integrated Woz Machine (IWM)
- FTDI (a series of USB to serial converter chips also supporting a bit bang mode)
- 2MGUI (a DOS driver by Ciriaco García de Celis utilizing bit-banging to support non-standard ultra-high capacity floppy disk formats "bypassing" the normal floppy controller logic, a similar program for Amiga floppies is Vincent Joguin's Disk2FDI)
- Light pen (on MDA, HGC, CGA and EGA PC-compatible graphics cards the sensor of an optional light pen could be read in a fashion similar to bit banging)
- Virtual machine (VM) (implementing virtual device drivers emulating actual hardware controllers sometimes involves utilizing programming techniques similar to bit banging)
- Software-defined radio (SDR)
- Polling (computer science)
References
[edit]- ^ "Analog Devices Glossary of Electrical Engineering (EE) Terms". Retrieved 2024-09-22.
- ^ Predko, Michael (2000). Programming and customizing PICmicro microcontrollers (2nd ed.). McGraw-Hill Professional. pp. 10–12. ISBN 978-0-07-136172-9.
External links
[edit]- Asynchronous serial (RS-232)
- I²C bus
- SPI bus
